上海秉奇阀门有限公司

英国GRIMM格林进口气动隔膜泵 UK GRIMM imp0rted pneumatic diaphragm pump

英国GRIMM格林进口气动隔膜泵概述： 

          进口气动隔膜泵是英国格林研制开发的新三代气动隔膜泵，采用压缩空气为动力源，是一种由膜片往复变形造成容积变化的容积泵。具有质量可靠、使用寿命长、噪音底、震动小、永不死机、做工精细等六大优点，即能抽送流动的液体，又能输送一些不易流动的介质，具有自吸泵、潜水泵、屏蔽泵、泥浆泵和杂质泵等输送机械的许多优点。

 

 

英国GRIMM格林进口气动隔膜泵工作原理：

1、压缩空气为动力。
2、是一种由膜片往复变形造成容积变化的容积泵，其工作原理近似于柱塞泵，由于隔膜泵工作原理的特点，因此隔膜泵具有以下特点：
⑴隔膜泵不会过热：压缩空气作动力，在排气时是一个膨胀吸热的过程，气动泵工作时温度是降低的，无有害气体排出。
⑵隔膜泵不会产生电火花：气动隔膜泵不用电力作动力，接地后又防止了静电火花。
⑶隔膜泵可以通过含颗粒液体：因为容积式工作且进口为球阀，所以不容易被堵。

 

英国GRIMM格林进口气动隔膜泵性能特点：
1、不需灌引水，吸程最高达7.6m，扬程达84m，出口压力≥7bar。
2、流动宽敞，通过性能好，允许通过最大颗粒直径达9.4mm。抽送带泥浆、杂质时，对泵磨损甚微。
3、扬程、流量可通过气阀开度实现无级调节(气压调节在1～7bar之间)。
4、该泵无旋转部件，没有轴封，隔膜等抽送的介质与泵的运动部件、工件介质完全隔开，所输送的介质不会向外泄漏。所以抽送有毒、易挥发或腐蚀性介质时，不会造成环境污染和危害人身安全。
5、不必用电，在易燃、易爆场所使用安全可靠。
6、可以浸没在介质中工作。
7、使用方便、工作可靠、开停只需简单地打开和关闭气体阀门，即使由于意外情况而长时间无介质运行或突然停机泵也不会因此而损坏，一旦超负荷，泵会自动地停机，具有自我保护性能，当负荷恢复正常后，又能自动启动运行。
8、本泵无须用油润滑，即使空转，对泵也无任何影响，这是该泵最大特点。
9、结构简单、易损件少，该泵结构简单，安装、维修方便，泵输送的介质不会接触到配气阀，联杆等运动部件，不像其他类型的泵因转子、活塞、齿轮、叶片等部件的磨损而使性能逐步下降。
10、可输送较粘的液体(粘度在1万厘泊以下)。

英国GRIMM格林进口气动隔膜泵技术参数： 

最大流量：18.9-1041L/min
最大扬程：70-84m
出口压力：0.7-0.84MPa
口       径：10-125mm
入气口径：1/4、1/2、3/4
颗粒直径：1.5-10mm
最大虹吸高度(干抽或湿抽)：2.4-7.6m
最大输送固体颗粒：1.5-9.4mm
最大空气消耗量：9.0-82.6scfm
每行程流量：(小口径)23cc
每往复流量：46cc、3.9-7.6L
最大往复速度：(小口径：干运转320cpm，湿运转250cpm)；135-400cpm

 

 

英国GRIMM格林进口气动隔膜泵主要用途： 

1、泵吸油漆、树胶、颜料。
2、粘合剂和胶水、全部种类可用泵吸取。
3、泵吸花生酱、泡菜、土豆泥、小红肠、果酱苹果酱、巧克力等。
4、各种瓦、瓷、砖器及陶器釉浆。
5、油井钻好后，用泵吸沉积物及灌浆。
6、泵吸各种乳剂和填料。
7、泵吸各种污水。
8、用泵为油轮，驳船清仓吸取仓内污水。
9、啤酒花及发酵粉稀浆、糖浆、糖密。
10、泵吸矿井、坑道、隧道、选矿、矿渣中的积水。泵吸水泥灌浆及灰浆。
11、各种橡胶浆。
12、各种磨料、腐蚀剂、石油及泥浆、清洗油垢及一般容器。
13、可以吸各种剧毒、易燃、易挥发液体。
14、各种强酸、强碱、强腐蚀液体。
15、吸各种高温液体最高可耐150℃。
16、作为各种固液体分离设备的前级送压装置。

海事            排放和输送                                ◆污水  ◆海水  ◆柴油
电子            排放和输送                                ◆废水  ◆强酸  ◆强碱
汽车            排放和输送                                ◆密封剂  ◆粘结剂  ◆电镀溶剂  ◆溶剂  ◆油漆

化工生产     排放和输送                                ◆肥皂  ◆清洁剂  ◆粘合剂  ◆油墨清洁/擦亮剂
                                                                    ◆油漆/染料  ◆针对剪切敏感物料
煤矿            排放                                          ◆污水  ◆混水  ◆稀泥浆
医药            食物及药物物料供应和输送       ◆FDA物料

UK GRIMM imp0rted pneumatic diaphragm pump summary:

       imp0rted pneumatic diaphragm pump is a new three generation pneumatic diaphragm pump developed by Green in Britain. It uses compressed air as power source. It is a displacement pump caused by reciprocating deformation of diaphragm. With reliable quality, long service life, low noise, small vibration, never crashes, six major advantages of working fine, the flow of liquid can be pumped, and easy to transport some of the flow medium has many advantages, self suction pump, submersible pump, shield pump, pump mud and impurities such as conveyor equipment.

 

UK GRIMM imp0rted pneumatic diaphragm pump working principle:

 

 

1. Compressed air as the driving force.

2. Is a diaphragm reciprocating deformation caused by volume changes in the displacement pump, its working principle similar to the plunger pump, because of the diaphragm pump working principle of the characteristics, so diaphragm pump has the following characteristics:

The diaphragm pump does not overheat: Powered by compressed air in the exhaust is an endothermic process of expansion, the pneumatic pump when the temperature is lower, no harmful gas emissions.

The diaphragm pump does not produce spark: pneumatic diaphragm pumps do not have electricity for power, ground and later to prevent electrostatic spark.

The diaphragm pump liquid containing particles can be: because the volume of imp0rts and working for the ball, so can not be easily blocked.

 

UK GRIMM imp0rted pneumatic diaphragm pump performance characteristics: 

 

 

 

1. Without irrigation water, suction lift up to 7.6m, head of 84m, the outlet pressure is greater than or equal to 7bar.

2. Wlow spacious, through good performance, allowing the maximum particle diameter of 9.4mm. Pumping with mud and impurities, little wear on the pump.

3. Head, flow can be achieved through the opening of the valve stepless adjustment (air pressure between 1 ~ 7bar).

4. The pump has no rotary parts, no seals, moving parts, medium diaphragm pump pumping and pump completely separated from the workpiece medium, the transmission medium does not leak out. Pumping so toxic and flammable or corrosive media, it will not cause environmental pollution and harm personal safety.

5. Do not use electricity. It is safe and reliable in flammable and explosive places.

6. Can be immersed in the medium work.

7. Easy to use, reliable, open stop simply open and close the gas valve, because of unforeseen circumstances even if long time no medium operation or sudden stop pump will not be damaged, once over loading, the pump will automatically shut down, with the self protection function. When the load is recovered, and can automatically start running.

8. The pump does not need oil lubrication, even idling, no impact on the pump, which is the biggest feature of the pump.

9. Simple structure, less wearing parts, the pump has the advantages of simple structure, convenient installation and maintenance, pump transmission medium will not come into contact with the valve rod and other moving parts, unlike other types of pumps due to the rotor wear, piston, gear and vane parts such as the gradual decline in performance.

10. Can carry more viscous liquid (viscosity at below 10 thousand CPS).

UK GRIMM imp0rted pneumatic diaphragm pump technical parameter:

 

 

 

 

 

 

Maximum flow: 18.9-1041L/min

Maximum lift: 70-84m

Outlet pressure: 0.7-0.84MPa

Caliber: 10-125mm

Inlet caliber: 1/4, 1/2, 3/4

Particle diameter: 1.5-10mm

Maximum siphon height (dry or wet):2.4-7.6m

The largest transport solid particles: 1.5-9.4mm

Maximum air consumption: 9.0-82.6scfm

Flow per stroke: (small bore) 23cc

Per reciprocating flow: 46cc, 3.9-7.6L

Maximum reciprocating speed: (small bore: dry running 320cpm, wet running 250cpm); 135-400cpm

UK GRIMM imp0rted pneumatic diaphragm pump main use:

 

 

 

 

 

1. Pump paint, gum, paint.

2. Adhesives and glue, all kinds can be pumped.

3. Pump peanut butter, pickles, mashed potatoes, red sausage, jam, apple sauce, chocolate, etc..

4. All kinds of tile, porcelain, brick and ceramic glaze slurry.

5. After oil well is drilled, pump the sediment and grout.

6. Pump various kinds of emulsion and packing.

7. Pumping all kinds of sewage.

8. Use the pump as an oil tanker, barge clearance, absorb the sewage inside the warehouse.

9. Hops and baking powder, pulp, syrup, sugar tight.

10. Pumping water, mine, tunnel, tunnel, ore dressing, water in slag. Suction cement grout and grout.

11. All kinds of rubber pulp.

12. All kinds of abrasive, corrosive oil and mud, grease and general cleaning container.

13. You can suck a variety of highly toxic, flammable, volatile liquids.

14. All kinds of strong acid, alkali and strong corrosive liquid.

15. All kinds of high temperature resistant liquid absorption maximum of 150 DEG C.

16. As a solid liquid separation equipment before the pressure delivery device.

 

UK GRIMM imp0rted pneumatic diaphragm pump application area:

 

 

 

 

 

 

Maritime emissions and transport the sewage water - - Diesel

Electron emission and transportation - wastewater - acid - alkali

The automobile exhaust and conveying the sealant - - solvent - solvent - binder electroplating paint

Chemical production and delivery of the soap - discharge cleaning agent - adhesive - ink cleaner / polishes

The paint / dye - for shear sensitive materials

The coal mine sewage emissions - water - dilute mud

Medical supplies and food and drug delivery material - FDA

进口气动隔膜泵官网：http://www.021fmc.cn/aspcms/product/2017-7-20/2766.html 

 

GRIMM中国：

      上海秉奇阀门有限公司为GRIMM公司在中国的总代理，是中国拥有GRIMM代理权及销售权，主要为中国地区客户提供服务与技术支持，同时，秉奇人员也积极参与总部技术培训学习，并不断掌握产品原理、实际运作、工程技术做为基石，完善对中国地区客户需求。             

关于GRIMM：

             英国格林（GRIMM）国际有限公司是亚太地区流体控制领域的主要生产和供应商之一，公司总部位于克莱福德，拥有一支有经验的研发队伍，实行全球统一设计，统一标准，在水泵领域内处于领先地位。在许多个国家均有生产水泵基地，中国由上海秉奇阀门负责中国市场各项业务与技术支持中心，同时向中国市场销售。

         英国格林（GRIMM）产品已广泛应用于市政给排水、建筑、石油、化工、液化气、食品、制药、发电、冶金、矿产、锅炉蒸汽系统、压力容器、原子能、航空、火箭等各领域，以及人们日常生活中。

         英国格林（GRIMM）主要产品有：管道泵、离心泵、隔膜泵、磁力泵、真空泵、潜水泵、排污泵、计量泵、卫生级泵、罗茨风机等系列产品。

服务体系：

GRIMM品质：

    GRIMM公司注重产品质量及使用寿命，全部采用先进制造技术和生产设备，并坚持不懈研发新产品，为确保不间断的全过程质量控制，在生产过程中采用(SPC)过程控制和(TQM)全面质量管理；GRIMM的严格规范实现了不让品质拖节，有效保障产品每个细节达到的性能指标。

GRIMM专业：

    掌握核心的流体控制技术，提供市场领先的产品、服务和解决方案，帮助用户提高效率，带来至关重要的基础设施。

GRIMM服务：

    我们与用户紧密合作，支持一系列系统使用技术和文件报告，提供售前、售中、售后服务和技术支持，有了您的信任与支持，我们将更完善、更高效提供水泵流体技术方案。

GRIMM china:

         Shanghai Bingqi Valve Co., Ltd. for GRIMM company general agent in China, is China with GRIMM proxy and sales rights, provide service and technical support, mainly for Chinese customers at the same time, will also actively participate in the training of technical personnel of butterfly learning headquarters, and continue to grasp the product principle, practical operation and Engineering Technology based on customer demand, improve the Chinese area.

ab0ut GRIMM:

         Uk GRIMM International Co., Lid is the field of fluid control in the Asia Pacific region is one of the main production and suppliers, the company headquarters is located in Clay Forde, has an experienced R & D team, the implementation of a global unified design, unified standards, a leading position in the field of water pump. In many countries, there are production pump base, China by the Shanghai Bingqi valve, responsible for the Chinese market business and technical support center, while selling to the Chinese market.

       Uk GRIMM products have been widely used in various fields for municipal drainage, construction, petroleum, chemical, gas, food, pharmaceutical, power generation, me-tallurgy, mining, boiler steam system, pressure vessel, atomic energy, aerospace, rockets, and people's daily life.

       Uk GRIMM the main products are: pipeline pump, centrifugal pump, diaphragm pump, magnetic pump, vacuum pump, submersible pumps, sewage pumps, metering pumps, sanitary pump, blower and other products.

Service system:

GRIMM quality:

         GRIMM company pays attention to product quality and service life, all adopt the advanced manufacturing technology and production equipment, and unremittingly research and development of new products, the whole process of quality control to ensure uninterrupted, used in the production process (SPC) process control (TQM) and total quality management; strictly regulate the implementation of GRIMM has not let the quality drag day, effectively guarantee the performance of each product details.

GRIMM major:

          Fluid control technology master core, market leading products, services and solutions that help users improve efficiency, bring critical infrastructure.

GRIMM service:

          We work closely with the user, support a series of system using technology and file reports provide pre-sale, sale, customer service and technical support services, with your trust and support, we will be more perfect and more efficient to provide technical solutions of fluid pump.

英国格林总代理商：上海秉奇阀门有限公司，微信咨询：

Uk GRIMM total agents: Shanghai Bingqi Valve Co., Ltd., WeChat Advisory:

 

Welcome new and old customers call negotiate!

Contacts：Huang Tianxiang

QQ：673088832

Mobile Phone:13524269805 (微信同号）

Company Phone:021-51698378

Add:Lane 51, dragon road, Shanghai, Xuhui District