上海秉奇阀门有限公司

英国GRIMM格林进口凸轮转子泵 UK GRIMM Inlet cam rotor pump

英国GRIMM格林进口凸轮转子泵概述：

          进口凸轮转子泵又称胶体泵、凸轮泵、三叶泵、万用输送泵等，转子泵属于容积泵，输送流量可以较精确的控制也可方便地制成变量泵。此泵的转速很低，一般在200rpm至600rpm之间，被输送的物料被平稳地输出而其成份不会受到破坏。可用于输送粘度很高的物质也可以方便地制成输出压力较高的品种。根据客户管道连接方式的需要，可做成上进下出型转子泵，根据客户安装方式及生产的需要，可做成移动型转子泵，根据客户调节转速及流量的需要，可做成变频调速型转子泵。
          转子泵依靠两同步反向转动的转子(齿数为2—4)在旋转过程中于进口处产生吸力(真空度)，从而吸入所要输送的物料。两转子将转子室分隔成几个小空间，并按a→b→c→d的次序运转。运转至位置a时，只有一室中充满介质；到位置b时，B室中封闭了部分介质；到位置C时，A室中也封闭了介质；到位置d时，A室B室与二室相通，介质即被输送至出料口。如此循环往复，介质(物料)即被源源不断输送出去。
          转子泵采用联轴整体组装，使体积变小（长度可以减短100-250mm），减少占地面积，结构紧凑，外包不锈钢，镜面抛光，外形美观，档次高，避免原来涂膏刷漆的脱落。性能优化：采用联轴整体组装，减少弹性联轴器功率消耗，噪音及磨损更换而提高工作效率，得到了最高的效率，最小的内部滑动和更长的使用寿命。
不同形状的转子具有不同的效果，具体分为以下几大类：
一叶转子：适用于输送含有大颗粒物料的介质，对大颗粒物料的破碎率较低，但其脉动大，压力低，容积量小，很少使用。
二叶转子：适用于输送含有中小颗粒物料的介质，对中小颗粒物料的破碎率相对较低，略有脉动，容积量小于三叶转子。
三叶转子：通用的转子类型，容积量大于其他类型的转子，各种性能指标优于一叶，二叶转子，但其在输送物料的过程中对颗粒物料有一定的破碎率。
传动的选择：
1、电机＋定整比减速器：这样的传动方式简单，转子的转速恒定，也就是决定了流量的不可调性。
2、电机＋机械摩擦式无级变速器：这种变速器的变速靠手动调节来实现，其特点是安全可靠，扭距大，流量无极可调，缺点是非自动调节，较麻烦，调速在运转过程中进行，不得在停机状态下调速，其使用维护参照制造商的使用说明书。
3、变频电机＋变频器：这种方式可实现转速的自动调节，亦即实现了流量的无级调速。其优点是自动化程度高，低速扭距较大，缺点是变频器的价格较高，其使用维护参照制造商的使用说明书。

英国GRIMM格林进口凸轮转子泵特点：

1、本泵中凡与输送物料接触的零配件，均采用符合卫生标准的不锈钢材料制作，其密封件均采用无毒橡胶。可靠的防锈性和无毒密封性确保了安全卫生。
2、转子的流线结构以及转子室中无死点和非金属件，避免了对被输送物质造成污染。
3、适合于就地CIP清洗与蒸汽消毒，完全符合美国FDA规范要求及医药级(GMP)规范要求。
4、特别适用于在输送过程中容易其泡沫以及输送高粘度、浓度及任何含颗粒的介质，经其输送的物料保持原有品质不变，不起任何理化反应。
5、采用外装动、静环式机械密封，可直接水冲洗，耐高压，不易磨损，无泄漏。
6、体积小，流量大，扬程压力高，适用长距离与高阻力定量输送。
7、泵的叶轮与传动齿轮分开，且在泵腔内各零配件之间保证一定的间隙，相互不接触，无磨损，低噪音，可靠性好，使用寿命长，节能降耗。
8、配置变频器后，可以随意调节流量，并可做一般计量泵使用。
9、可输送汽、液、固等三相混合物料。可以输送的介质的粘度可高1000000CP和含固量达55%的浆料。
10、结构紧凑，维护方便，几乎无易损件，运行成本低。
11、它不仅具有一般转子泵的的特点，并且在输送高粘度及内含较大颗粒的物料时，也具有一定的优势，对特别粘稠的物料也能够有效输送。经其输送的物料保持原有品质不变。
英国GRIMM格林进口凸轮转子泵技术参数：
流       量：0.1-200m3/h
系统压力：0.1-1.2MPa
转       速：100-720r/min
功       率：0.12-185KW
进出口径：10-200mm
粘       度：1-1000000cp
密       封：A：机械密封
                 B：水冷机械密封 
                 材料：硬质合金、碳化硅、氮化硅、石墨、陶瓷等 
                 C：填料密封
                 材料：聚四氟乙烯纤维、碳素纤维、含石墨芯碳纤维等
材       质：304、304L、316、316L
工作方式：间歇式、连续
连接方式：法兰、螺纹、卡箍
安装方式：固定式、移动式

英国GRIMM格林进口凸轮转子泵应用领域：

日用化工：AES、LAS、AOS、K12、甘油、山梨醇、脂肪醇、沐浴露、护肤霜、洗发液、洗手液、牙膏、肥皂、洗衣粉料浆等。 
精细化工：染料、颜料、各种浆料、化工助剂、粘胶剂、104胶、、硅油皮革油、乳化炸药各种胶体料等。
食       品：巧克力、炼乳、酸奶、蜂蜜、糖浆、蔗糖、番茄汁、浓缩果汁、果酱、冰激凌、牛奶、酵母泥浆、肉浆、果冻、酸奶、调味品、酒精、大豆蛋白、面粉浆等。
造       纸：聚丙烯酰胺（PAM）、碳酸钙、淀粉糊、羧基丁苯/丙苯乳胶、松香、松香胶、纸浆、填料、干强剂、湿强剂、施胶剂、助留助滤剂、消泡剂、涂布、水处理化学品等。
化       纤：粘胶浆粥、PVA、维纶浆料、腈纶浆料、胺纶浆料、聚酯切片、涤纶、丙纶、人造纤维、功能性纤维等。
医       药：各种药膏、浸膏、药乳液、药丸糊、糖浆、保健品、药剂等。
涂       料：油漆、涂料、油墨、绝缘漆、树脂、助剂、有机溶剂等。 

UK GRIMM Inlet cam rotor pump summary:

         imp0rted cam rotor pump, also known as colloid pumps, cam pumps, three leaf pumps, pumps and so on, the rotor pump is a displacement pump, the flow can be more accurate control, but also can be easily made variable pump. The speed of the pump is very low, generally between 200rpm to 600rpm, the transported material is smoothly output, and its components will not be damaged. The utility model can be used for conveying materials with high viscosity, and can also conveniently produce varieties with higher output pressure. According to the needs of customers pipe connection, can make progress under the rotor pump, according to the needs of customers installation and production, can be made into a mobile type rotor pump, according to the needs of customers and the speed of flow regulation, can be made into a variable speed rotary pump.

        The rotor pump relies on two simultaneous, reverse rotating rotors (2 to 4 teeth) to generate suction (vacuum) at the inlet during the rotation so as to absorb the material to be conveyed. The two rotor divides the rotor chamber into a few small spaces and runs in the order of a, B, D, C. To the position of a running, only one room filled with medium; to position B, B encloses part of the medium; to the position of C, A in the room also closed to the media; the position of D, A room B chamber and the two chamber, the medium is transported to the discharge port. In this way, the medium (material) is transported continuously.

        The rotor pump adopts the whole shaft assembly, so that smaller size (the length can be shortened 100-250mm), to reduce the area, compact structure, coated with stainless steel, mirror polished, beautiful appearance, high grade, avoid dropping original paste paint. Performance Optimization: the overall assembly of the axle reduces the power consumption, noise and wear and tear of the elastic couplings, improves efficiency, achieves the highest efficiency, minimum internal sliding and longer service life.

Rotors of different shapes have different effects, and are divided into the following categories:

Blade rotor: suitable for conveying medium containing large particles of material, the crushing rate of large particles of material is low, but its large fluctuations, low pressure, small volume, rarely used.

Two blade rotor: suitable for conveying medium and small particles of materials, the crushing rate of small and medium-sized materials is relatively low, slightly pulsating, less volume than the trefoil rotor.

Three blade rotor: General rotor type, the volume is greater than other types of rotor, various performance indicators better than a blade, two blade rotor, but in the process of conveying materials, the particle material has a certain rate of fragmentation.

Transmission options:

1.Motor + fixed ratio reducer: this way of transmission is simple, the rotor speed constant, that is to determine the flow of non adjustability.

2.Motor + mechanical friction CVT: the transmission speed by manual adjustment to achieve, it is safe and reliable, large torque, flow rate is adjustable, drawback of non automatic adjustment, more trouble, control in the process of operation, not in the shutdown state governor, referring to the use of maintenance the manufacturer's instructions.

3.Frequency conversion motor + frequency converter: this method can realize the automatic adjustment of speed, that is to realize the stepless speed regulation of flow. The utility model has the advantages of high degree of automation, low speed large torque converter, disadvantage is the higher prices, the use of maintenance according to the manufacturer's instructions.

UK GRIMM Inlet cam rotor pump features Characteristic:

1.The pump and the delivery of materials contact parts and components, are in line with the hygiene standards of stainless steel materials, the seals are non-toxic rubber. Reliable rust prevention and non-toxic sealing, to ensure safety and health.

2.The flow structure of the rotor and the rotor chamber without dead center and non-me-tallic parts, to avoid the transport of material pollution.

3.Suitable for on-site CIP cleaning and steam disinfection, fully comply with the requirements of the United States FDA specification and pharmaceutical grade (GMP) specifications.

4.Especially suitable for conveying in the process of easy foam, and the delivery of high viscosity, concentration and any particle containing medium, the material transported by it to maintain the original quality unchanged, without any physical and chemical reaction.

5.Adopt external dynamic and static ring mechanical seals, which can be directly washed by water. It is resistant to high pressure, difficult to wear and no leakage.

6.Small size, large flow, high head pressure, suitable for long distance and high resistance quantitative transportation.

7.The impeller of the pump is separated from the drive gear, and a certain gap is ensured between the spare parts of the pump cavity, and the utility model has the advantages of no contact, no wear, low noise, good reliability, long service life, energy saving and consumption reduction.

8.After the configuration of frequency converter, you can freely adjust the flow, and can be used as a general metering pump.

9.Can transport steam, liquid, solid and other three-phase mixed material. The viscosity of the medium to be transported can be 1000000CP high and a slurry containing 55% solids.

10.Compact structure, easy maintenance, almost no wearing parts, low operating costs.

11.It not only has the characteristics of the general rotary pump, but also has some advantages in conveying high viscosity and large particles containing material, and it can also transport the material with very thick material. The material transported by it keeps the original quality unchanged.

UK GRIMM Inlet cam rotor pump technical parameters:

Flow rate: 0.1-200m3/h

System pressure: 0.1-1.2MPa

Speed: 100-720r/min

Power: 0.12-185KW

Inlet & Outlet: 10-200mm

Viscosity: 1-1000000cp

Seal: A: mechanical seal

         B: water-cooled mechanical seal

         Material: carbide, silicon carbide, silicon nitride, graphite, ceramics, etc.

         C: packing seal

         Material: polytetrafluoroethylene fiber, carbon fiber, graphite core, carbon fiber and so on

Material: 304, 304L, 316, 316L

Mode of work: intermittent, continuous

Connection: flange, thread, clamp

Installation: fixed type, mobile type

UK GRIMM Inlet cam rotor pump applications:

Daily chemical industry: AES, LAS, AOS, K12, glycerol, sorbitol, fatty alcohol, bath lotion, skin cream, shampoo, soap, toothpaste, soap, washing powder slurry etc..

Fine chemical dye, pigment, various pulp, chemical additives, adhesives, rubber, leather, 104 silicone oil, a variety of materials such as colloid emulsion explosive.

Food: chocolate, milk, yogurt, honey, syrup, sucrose, Tomato Juice, concentrated juice, jam, ice cream, milk, yeast mud, meat pulp, jelly, yogurt, spices, alcohol, soy protein, flour paste etc..

Paper: polyacrylamide (PAM), calcium carbonate, starch paste, carboxylated styrene butadiene/styrene acrylic latex, rosin, rosin, pulp, filler, dry strength agent, wet strengthening agent, sizing agent, retention agent, defoaming agent, coating, water treatment chemicals etc..

Chemical fiber: sticky mucilage porridge, PVA, PVA slurry, slurry, slurry, acrylic amine aramid polyester and polyester, polypropylene fiber, synthetic fiber, functional fiber etc..

Medicine: all kinds of ointment, extract, medicine emulsion, pills, paste, syrup, health care products, drugs and so on.

Paint: paint, coating, printing ink, insulating paint, resin, auxiliary agent, organic solvent, etc.

进口凸轮转子泵官网：http://www.021fmc.cn/aspcms/product/2018-5-7/1269.html  

 

GRIMM中国：

    上海秉奇阀门有限公司为GRIMM公司在中国的总代理，是中国拥有GRIMM代理权及销售权，主要为中国地区客户提供服务与技术支持，同时，秉奇人员也积极参与总部技术培训学习，并不断掌握产品原理、实际运作、工程技术做为基石，完善对中国地区客户需求。             

关于GRIMM：

          英国格林（GRIMM）国际有限公司是亚太地区流体控制领域的主要生产和供应商之一，公司总部位于克莱福德，拥有一支有经验的研发队伍，实行全球统一设计，统一标准，在水泵领域内处于领先地位。在许多个国家均有生产水泵基地，中国由上海秉奇阀门负责中国市场各项业务与技术支持中心，同时向中国市场销售。

       英国格林（GRIMM）产品已广泛应用于市政给排水、建筑、石油、化工、液化气、食品、制药、发电、冶金、矿产、锅炉蒸汽系统、压力容器、原子能、航空、火箭等各领域，以及人们日常生活中。

       英国格林（GRIMM）主要产品有：管道泵、离心泵、隔膜泵、磁力泵、真空泵、潜水泵、排污泵、计量泵、卫生级泵、罗茨风机等系列产品。

服务体系：

GRIMM品质：

       GRIMM公司注重产品质量及使用寿命，全部采用先进制造技术和生产设备，并坚持不懈研发新产品，为确保不间断的全过程质量控制，在生产过程中采用(SPC)过程控制和(TQM)全面质量管理；GRIMM的严格规范实现了不让品质拖节，有效保障产品每个细节达到的性能指标。

GRIMM专业：

       掌握核心的流体控制技术，提供市场领先的产品、服务和解决方案，帮助用户提高效率，带来至关重要的基础设施。

GRIMM服务：

       我们与用户紧密合作，支持一系列系统使用技术和文件报告，提供售前、售中、售后服务和技术支持，有了您的信任与支持，我们将更完善、更高效提供水泵流体技术方案。

GRIMM china:

         Shanghai Bingqi Valve Co., Ltd. for GRIMM company general agent in China, is China with GRIMM proxy and sales rights, provide service and technical support, mainly for Chinese customers at the same time, will also actively participate in the training of technical personnel of butterfly learning headquarters, and continue to grasp the product principle, practical operation and Engineering Technology based on customer demand, improve the Chinese area.

ab0ut GRIMM:

         Uk GRIMM International Co., Lid is the field of fluid control in the Asia Pacific region is one of the main production and suppliers, the company headquarters is located in Clay Forde, has an experienced R & D team, the implementation of a global unified design, unified standards, a leading position in the field of water pump. In many countries, there are production pump base, China by the Shanghai Bingqi valve, responsible for the Chinese market business and technical support center, while selling to the Chinese market.

       Uk GRIMM products have been widely used in various fields for municipal drainage, construction, petroleum, chemical, gas, food, pharmaceutical, power generation, me-tallurgy, mining, boiler steam system, pressure vessel, atomic energy, aerospace, rockets, and people's daily life.

       Uk GRIMM the main products are: pipeline pump, centrifugal pump, diaphragm pump, magnetic pump, vacuum pump, submersible pumps, sewage pumps, metering pumps, sanitary pump, blower and other products.

Service system:

GRIMM quality:

         GRIMM company pays attention to product quality and service life, all adopt the advanced manufacturing technology and production equipment, and unremittingly research and development of new products, the whole process of quality control to ensure uninterrupted, used in the production process (SPC) process control (TQM) and total quality management; strictly regulate the implementation of GRIMM has not let the quality drag day, effectively guarantee the performance of each product details.

GRIMM major:

          Fluid control technology master core, market leading products, services and solutions that help users improve efficiency, bring critical infrastructure.

GRIMM service:

          We work closely with the user, support a series of system using technology and file reports provide pre-sale, sale, customer service and technical support services, with your trust and support, we will be more perfect and more efficient to provide technical solutions of fluid pump.

英国格林总代理商：上海秉奇阀门有限公司，微信咨询：

Uk GRIMM total agents: Shanghai Bingqi Valve Co., Ltd., WeChat Advisory:

 

Welcome new and old customers call negotiate!

Contacts：Huang Tianxiang

QQ：673088832

Mobile Phone:13524269805 (微信同号）

Company Phone:021-51698378

Add:Lane 51, dragon road, Shanghai, Xuhui District